|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
- Very good scan quality, PERFECT!
- Sehr gute scan Qualitaet, empfehlenswert!
Wolfgang Sundhaus
 ;
Good site, works ok and you get what you order, no problems experienced, got my manual within a day. A++++
;
Original well scanned manual. Got the job done. Microwave problem found & corrected. For $5 and a new magnitron from ebay, it was a cheap and good the first shot fix. Electrical schematics allowed me to mage sure every thing else was ok before cutting and order for parts. Hard to live without.
;
I was very skeptical of this website, I have never downloaded manuals before. I put it on the AMEX and payed through Paypal to ensure protection. I got the manual exactly as described and now I can replace the filter capacitor for this amp. Great Price, others selling for 12.99 or more and this is the same manual. I will search out this website for other manuals. Thank you
;
Manual was reasonably easy to follow. I am not an engineer or know much about electronics but with the manuals help I was able to figure out the problem, identify the part required for the repair. Replacement part cost around $30. Whilst replacing the part I was telling myself, "this aint gonna work cos it seems far too easy". Took about 15 minutes to do and my plasma TV works a treat. Would never have been able to do this without the service manual.
6. Feed a white raster signal through RGB connectors and turn on the power of the projector. (If a signal generator which provides a white raster signal is not available, turn on the power without connecting the LCD panel.) 7. If all three LCD panels need to be replaced, refer to the �Green LCD adjustment�. 8. Adjust the focus ring and the raster focus of the LCD which has not been replaced. If the green LCD is not replaced, adjust the green raster. If the green LCD is replaced, adjust the red raster, and if the red LCD is replaced, adjust the blue raster. 9. Atach the wall chart to the wall so the bottom line of the square lines up with the bottom of the raster. Also, center the chart horizontally with the raster. 10. Adjust the zoom ring and make sure the bottom of the raster remains on the bottom line. Return the zoom ring to the maximum wide setting. 11. Hereafter, do not move the setting position and the focus ring.
5. If the focus or raster geometry is changed, when tightening the screws holding the LCD mount, loosen the screws slightly and readjust. 6. Prepare one focus adjustment jig and insert it onto the one hole on top of the LCD plate, and adjust the LCD plate back and forth until the best focus is obtained in considering upper and lower balance of the projection screen. (Refer to Fig. 3-2-7.) 7. If the focus or raster geometry is changed, when tightening the screws holding the LCD mount, loosen the screws slightly and readjust. 8. Input the cross hatch pattern of G signal. 9. Adjust the cross hatch pattern up & down (Refer to Fig. 3-2-8) and left & right (Refer to Fig. 3-2-9) with the three adjusting screws (hex screw driver (1.0 mm) available on the market) until it is aligned with the green cross hatch pattern.
< Red/Blue LCD adjustment > 1. Confirm connection of the LCD panel (if not connected, connect the LCD to the connector of the PC board.) 2. Turn the projector on. 3. Input the cross hatch pattern from RGB connectors. Only input R signal when adjusting the red panel focus, and only input B signal when adjusting the blue panel focus. 4. Prepare two focus adjustment jigs. Insert them onto two holes on bottom of the LCD plate, and adjust the LCD plate back and forth until the best focus is obtained in considering left and right balance of the projection screen. Fig. 3-2-8
Fig. 3-2-9 10. Turn off the power, and remove the FPC section of the LCD from the connector of the drive PC board.
Fig. 3-2-7
1-7
|
|
|
> |
|
