|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It took about 24-hours after my payment before I was able to get to the download. Apparently, payment processing is not 100% automated. That is no big deal, just be aware of that going in.
After I got to it, it was in good shape, easy to read, etc. Not some cheap FAX copy looking thing.
Also, this site was the cheapest I found. Another Plus!
 ;
Good price, very legible manual, exactly what I needed -- but had to wait a day to actually get the download of the manual. Would have preferred to download it immediately after payment rather than waiting for someone to "process" my order. I was surprised that I had to wait that long.
;
As the only source for this manual it rather rank quite high since it is well scanned and perfectly readable.
;
the manual is in good quality and it's in pdf. manual was send in less then 24h.
regards
mike
;
I would not plug this machine in without finding a manual like this. In addition to setup and normal operating instructions, it has troubleshooting flowcharts, diagrammed mechanical adjustments, and schematics to beat the band. The tech I hand it to would be thrilled to find solder side PCB diagrams with component outlines superimposed, pinouts for every IC chip, and line drawings of transistors, with labeled legs.
As for printing quality, this may be a copy of a copy, but even the finest print when enlarged is very legible. There is a bit of grayed print over a few pages, as if a wet page were placed over it, but the print is still very legible. If you could borrow an original manual and get it printed and bound for 4 to 6 times the cost, you could get better quality. In that case you wouldn't be here. For price, utility, and availability I am rating this manual highly.
Menu screen adjustment:
� � Operate after inputting the following initial figures when replacing EEP ROM. These initial figures are only for reference purposes and meant for rough adjustment. Check the condition and adjust the area where the general repair is carried out.
TV-A2115 PAGE 1 1. H POS 2. V POS ����� 4. OSD H 5. PIF VCO 6. RF AGC PAGE 2 1. R CUT OFF 2. G CUT OFF 3. B CUT OFF 4. G DRV GAIN 5. B DRV GAIN 6. BRIGHT PAGE 3 1. SECAM B-Y 2. SECAM R-Y 3. RGB CONT 4. H SIZE 5. V SIZE 6. TINT
Initial Figures PAL (NTSC) 0B 03 �� 15 80 3F 7F 7F 7F 40 40 40 08 08 00 00 20 3F Fig. 1
Sample Indication for Adjustment Menu No.
Each adjustment should be carried out after checking the adjustment menu no. (Refer to the above Fig.)
PAGE 1
1-1. H POS Horizontal Positioning Adjustment PAL Adjustment Menu No. 14 (Page 1-1) Input signal : Crosshatch Measuring instrument : Pattern generator / PAL � Use the volume keys on the jig remote controller to adjust the dot mark in the centre of crosshatch screen to the exact centering position by allocating an equal number of squares on the left and right side of the dot. A=B (Fig. 1-1) NTSC Adjustment Menu No. 87 Input signal : Crosshatch Measuring instrument : Pattern generator / NTSC � Using the �CHANNEL� key, scroll through the adjustment menu and select No.87. To adjust, follow the same procedure as PAL.
1-2. V POS Vertical Positioning Adjustment PAL Adjustment Menu No.15 (Page 1-2) Input signal : Crosshatch Measuring instrument : Pattern generator / PAL � Using the volume keys on the jig remote controller, adjust the dot mark to the exact vertical centre position in the crosshatch screen. (Fig. 1-2) * In case of being unable to adjust by the above mentioned procedure, adjust S501. NTSC Adjustment Menu No. 86 Input signal : Crosshatch Measuring instrument : Pattern generator / NTSC � Use the �CHANNEL� key to scroll through the adjustment menu and select No. 86. To adjust, follow the same procedure as PAL. * Do not adjust S501 for NTSC.
� 14 �
|
|
|
> |
|
