|
|
|
Who's Online
There currently are 5905 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It is perfect, exactly what we needed. It's like the paper version but less clutter.
 ;
Received my manual within 24 hours. Very clear scan of the manual I needed. Thanks!
;
Very clear scan, I recommend it. Definitely a must have for any 3362 owner.
Alpine could have written a slightly more complete manual, though. It's already pretty huge, but the unit has so many functions, I feel some more explanation would have been better.
Yamaha's manual of their comparable YDSP-1 is a little better in my opinion.
;
Immediate response with excellent service - highly reccommended
;
Correct manual received and of good quality but the contents of the file for the Service Manual for the same monitor is for a 20" TV not the RGB Monitor.
English
Turning On the Power
To turn on the unit, press
STANDBY/ON
Adjusting the Tone (Bass/Treble)
You can adjust the bass level (low frequency range) and the treble level (high frequency range) within a range of �5 to +5. When shipped, the bass level set to �BASS 0� and the treble level set to �TREBLE +1.� � This function only affects the playback sound, and does not affect your recording. � There is a time limit in doing the following steps. If the setting is canceled before you finish, start over from step 1. On the remote control ONLY:
STANDBY/ON (or on the unit). The STANDBY lamp on the unit goes off. � When you press the source button �3/8 CD, 2 3 TAPE, TUNER (or BAND TUNER on the unit) and AUX, the unit automatically turns on and starts playback if the source is ready. To turn off the unit (standby), press STANDBY/ON (or on the unit) again. The STANDBY lamp on the unit lights on. � The CLOCK indicator and �0:00� flash on the display until you set the built-in clock. After setting the clock, the clock time will appear on the display while the unit is on standby. � A little power is always consumed even while the unit is on standby. To switch off the power supply completely, unplug the power cord.
1
Press BASS to adjust the bass level or press TREBLE to adjust the treble level.
BASS TREBLE
2
When you unplug the power cord or if a power failure occurs The clock is reset to �0:00� right away, while the tuner preset stations (see page 12) will be erased in a few days.
Press UP to increase the level or press DOWN to decrease it.
UP
DOWN
Reinforcing the Bass Sound
You can reinforce the bass sound to maintain rich, full bass at low volume�Active Hyper Bass Pro. � This function only affects the playback sound, and does not affect your recording. To get the effect, press AHB PRO so AHB PRO that the BASS indicator lights up on the display. � Each time you press the button, the bass reinforcement alternates between on (AHB ON) and off (AHB OFF). To cancel the effect, press AHB PRO again so that the BASS indicator goes off.
Adjusting the Volume
You can adjust the volume level only while the unit is turned on. The volume level can be adjusted between �VOL MIN� and �VOLUME 1� � �VOLUME 40 (VOL MAX).� Press VOLUME + to increase the volume or press VOLUME � to decrease it.
VOLUME
For private listening Connect headphones to the PHONES jack. No sound comes out of the speakers. Be sure to turn down the volume before connecting or putting on headphones. DO NOT turn the unit off (standby) with the volume set to an extremely high level; otherwise, the sudden blast of sound can damage your hearing, speakers and/or headphones when you turn on the unit or start playing any source next time. REMEMBER you cannot adjust the volume level while the unit is on standby.
11
|
|
|
> |
|
