SHARP XE-A202
Quick Start

Quick Start/A4New

03.6.10 0:38 PM

Page 1

XE-A202 Quick Start Guide

English

For quick set-up, follow the steps shown below. Note that malfunction may occur if you do not follow the steps. For further information, please read the instruction manual. Before setting up your cash register, prepare three new R6 or LR6 batteries (�AA� size), which are necessary for memory backup, and find a stable surface near an AC outlet where the cash register is not subject to water sources or direct sunlight.

1

Installing the Cash Register

2

Preparing the Cash Register

3

Installing the Paper Roll
(for receipt printing)

4

Basic Programming

Install the cash register using the fixing angle bracket provided with the register. 1. Thoroughly clean the location where the fixing angle bracket (B) is to be placed. 2. Peel off the adhesive tape on the fixing angle bracket. 3. Hook the angle bracket onto the hook (A) that is located at the bottom rear of the register. 4. Firmly stick the fixing angle bracket to the table surface that your cleaned above.

Initializing the Cash Register
To ensure the cash register operates properly, initialize it using the following procedure. 1. Make sure the AC power cord is unplugged and batteries are not installed on the register. 2. Insert the manager (MA) key into the mode switch and turn it to the REG position. 3. Insert the plug of the AC power cord into the AC outlet. A buzzer will sound three times. IMPORTANT: This operation must be performed without batteries installed. 4. The register display should now show � 0.00�.
OPX/Z REG MGR X1/Z1 X2/Z2 PGM

1. Lift up the print roller release lever to unlock and open the print roller arm
Print roller arm

Set the mode switch to the PGM position.

Setting the Date
Print roller release lever

Enter the date in 8 digits using the daymonth-year format. Then press s. Example: Date (26 August, 2003)

26082003
2. Set a paper roll in the paper roll cradle as per the diagram.
To the printer Correct Incorrect To the printer

s

Setting the Time
Enter the time in 4 digits (�hhmm� format) using the 24 hour system. Then press s. Example: Time (2:30 p.m.)

3. Feed the end of the paper along with the paper positioning guides as per the diagram.
Paper positioning guides

NOTE: If the buzzer does not sound when the plug is inserted, the initialization has not been done successfully. Wait at least one minute after pulling out the plug, and insert the plug again.

1430

s

Setting the VAT
Set the VAT rate in seven digits (3-digit integer and 4-digit decimal). Example: VAT1 rate 16%

Installing the Batteries
Install three new R6 or LR6 batteries (�AA� size) according to the procedure shown below with the power cord
A

B

connected and set the mode switch to REG position. 1. Lift the rear of the printer cover and detach it.

4. While keep holing down the paper, close the print roller arm slowly, and push down the arm until you hear a click sound to lock the arm. The paper will be fed automatically.

s 9 @ 1 @ 16 @ sA
NOTE: Department 1 to 50 are set to VAT1 by default.

To remove the resister from the fixing angle bracket: 1. Lift up the front of the register and pull the register towards you.

Other programming
While the cash register is preprogrammed so that it can be used with minimal setup, you may need to program some items such as department texts and logo message. For details of programming, please refer to the instruction manual.

2. Open the battery compartment cover. 5. Cut off the excess paper using the edge of the inner cover, and replace the printer cover. Press the F key to make sure the paper end comes out of the printer cover and clean papar face appears.

3. Install three new R6 or LR6 batteries (�AA�size) as per the diagram. When the batteries are properly installed � � on the display will disappear. 4. Close the battery compartment cover.

5

Now, you are ready for sales entries.

NOTE: If you want to use a paper roll for journal printing, please refer to GETTING STARTED section of the instruction manual.

Set the mode switch to the REG position, and start registration. For details of registration, please refer to the instruction manual.